SPRAY FIREPROOFlNG—ASTM STANDARDS. ASTME E — Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material. ASTM-Epdf – Download as PDF File .pdf), Text File .txt) or read online. Description: Standard Test Methods for Thickness and Density of Sprayed Fire- Resistive Material (SFRM) Applied to Structural Members. View More. Standard.
|Published (Last):||7 April 2014|
|PDF File Size:||2.92 Mb|
|ePub File Size:||6.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
This method measures the volume of the material without the need for thickness or area measurements. The values stated in each e650 may not be exact equivalents; therefore, each system shall be used independently of the other. These include sprayed fiber and cementitious types.
Astm e605 measurements are concerned with the application of astm e605 SFRM, while the density measurements pertain to the product itself.
This change has drastically increased astm e605 amount of testing on fluted decks. It would be appropriate to mention the alternate method for astm e605 the in-place density stated, in ASTM E Section 8. E conducts thickness testing at a Rate of one bay per floor or one bay for each 10, sq.
He stated the following: Since you suspect astm e605 improper application, it would be prudent to test the SFRM in the standard method and to also cut around the cap and test just for adhesiveness and report the findings to the design professional.
Testing Engineers – Case Studies
With such a significant discrepancy between the two can you explain the right procedure? Consult the rating criteria. If the density of the Astm e605 does not meet the design criteria can an increase of thickness compensate astm e605 the deficient density? It makes no reference to Note 4 in using a correction formula.
The apparatus, materials, and procedure used to apply the SFRM astm e605 laboratory tests shall be the same as is used for the construction of either of the test assemblies described in Test Methods E and E Historical Version s – view previous versions of standard.
It is based on the same design concept of the asm tested assembly but it is up to the astm e605 professional to determine if the astm e605 in thickness compensates for the low density of the SFRM.
However the user should be cautious as to the extent of the reference. This standard does not purport to address all of the safety concerns, if any, astm e605 with its e6605.
As a laboratory we asym the measurements should be actual not allowables. It is the astm e605 of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. From a practical viewpoint, the use of actual measurements for density calculations prevents “false high” density calculations.
My question is after setting the cap with epoxy and letting it set for approximately 24 hours are we to cut around the cap to astmm substrate or are we to astm e605 it in-place without cutting around the cap? While the wording in the manual seemed confusing, an appendix clarified that 12 thickness astm e605 should be taken.
Standard: ASTM E605
The apparatus, materials, d605 procedure used to apply the SFRM for laboratory tests shall be the same as is used for the construction of either of the test assemblies described in Astm e605 Methods E and E Astm e605 sample Operating Procedure follows: With such a conflict we refer to IBC It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Sstm concept of a correction formula has a valid basis and astm e605 not be considered as a loop hole or an easy way out. It is the intent of these test methods to provide procedures to determine these properties. However, this section does note that 12 thickness measurements are to astm e605 taken, and no statement is made regarding adjusting the average of the 12 measurements. The test methods are applicable to both laboratory and field procedures, astm e605 indicated in Section.
Cutting around the cap down to the astm e605 will isolate the bond strength to only adhesion and may there by indicate why astm e605 project sounds hollow astm e605 would not be a standard method to substantiate an unacceptable application of SRFM.
This would result in an overstatement of the protection level, which must be avoided. So, when writing an SOP for performing thickness determination the following could be adopted: The test methods are applicable to both laboratory and field procedures, as indicated in Section 7.
They further define adhesion as the property of sticking together as glue and wood or the joining of surfaces of different composition. The values given in parentheses are for information only.
During a recent project we found the Sprayed Fire-Resistive Material applied to the steel substrate to astm e605 hollow upon surface tapping. For SFRM astm e605 provide the required level of protection both the minimum average thickness and the density requirements must be met. Work Item s – proposed revisions of this standard. Astm e605 are correct, the averaging calculations for thickness measurements as mentioned in ASTM E section 8. These include sprayed fiber and cementitious types.
It reduces some of the measuring and sampling variables that are inherent with other methods. E conducts thickness testing at a rate of one bay per floor or one bay for each 10, sq.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
When this question was asked of Luke Woods of W. For every sq. The IBC uses E for thickness determination but has wording that supersedes E on the rate astm e605 testing. On the other hand, IBC And Note 4 states the following: If we go back to the IBC It can be used to retest a sample that may be in question. Active view current version of standard.
ICS Number Code Is this a contradiction and which frequency should be used? Link to Active Astm e605 link will always route to the astm e605 Active version of the standard.