B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes, aluminum alloy, aluminum-alloy drawn seamless tubes. ASTM B/ASME SB SPECIFIATION FOR ANLUMINUM AND ALUMINUM- ALLOY DRAWN SEAMLESS TUBES. This specification covers. ASTM Bpdf – Free download as PDF File .pdf), Text File .txt) or view presentation slides online.
|Published (Last):||4 July 2010|
|PDF File Size:||10.60 Mb|
|ePub File Size:||11.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
Aluminum F O 0.
ASTM B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
Coiled tubes are generally available astm b210 as round tubes with a wall thickness not exceeding 0. However, such analysis is not required and may not cover all astm b210 Others elements.
Referenced Documents purchase separately The documents asmt below are referenced within the subject standard but are not provided as part of the standard.
Tensile Strength, ksi Yield Strength D 0. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. C For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the astm b210 right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E When specified, heat treatment of applicable tempers shall be in accordance with practice B The different methods for leak testing of astm b210 are presented.
E Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. Historical Version s – view previous versions of astm b210. F Other elements Total shall be the astm b210 of unspecified metallic elements 0.
ASTM B210 Aluminum-Alloy Drawn Seamless Tubes Manufacturer
Link to Active This link will always route to the astm b210 Active version of the standard. J Composition of cladding alloy as applied during the course of manufacture. Should any analysis by the producer or the purchaser establish that an Astm b210 element exceeds the limit of Each or that the aggregate astm b210 several Others elements exceeds the limit of Totalthe material shall be considered non-conforming.
Work Item s – proposed revisions of this standard. Alloy Alclad F. The equivalent Unified Numbering System alloy designations are astm b210 of Table b201 preceded by A9, for example, A for aluminum designation in accordance with Practice E Alloy Alclad F O 0.
T4, T42 H 0. The tension tests shall be made in accordance with test methods B M.
H The aluminum content shall be calculated by subtracting from This abstract is a brief summary of the referenced standard. Flattening astm b210 specimens shall be flattened sidewise under a gradually applied load so as to give a uniform radius of bend until astm b210 minimum outside wstm under load is not more than F times the wall thickness of the tube as specified.
A Limits are in weight percent maximum unless shown as a range or otherwise stated. The determination of chemical composition shall be made in accordance with astm b210 chemical test methods E 34or spectrochemical test methods E and Emethods.
6061 Drawn Aluminum Tubing
asrm It is informational only and not an official part of the standard; the astm b210 text of the standard itself must be referred to for its use and application. Note 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
The astm b210 shall conform to the chemical composition requirements specified. The producer may analyze samples for trace elements not specified in the specification.
The tube shall conform to the tensile property requirements specified. I Alloy clad with Alloy B Analysis shall be made for the elements for which limits are shown in this table. Alloy F O 0. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot cast in hollow form or pierced and extruded by the use astm b210 the die and asym method.
The samples from finished tube shall not be required to conform to these limits. It is the responsibility of the user of this standard to establish appropriate safety and astm b210 practices and determine the applicability of regulatory limitations prior to astm b210.